Selasa, 06 Agustus 2013

how do you mow a lawn?

best lawn mower beer on Better All The Time Thanksgiving Dispatch #2
best lawn mower beer image



Chad


we just got our very first lawn mower and we dont know how to use it. we turn the key and nothing happens. there are places for u to unscrew a cap and it leads to know where but inside the engine. and i also dont know how to cut the grass. do you just run over it?
ahhahahahah that was a good one.!



Answer
Do you have the Black and Decker (electric) OR the Craftsman (gas).

Both require turning the key lifting the lever the Craftsman also requires you hold the lever while pulling the cord. The B&D needs to have the battery charged the Craftsman needs gas !

To cut the lawn.. Never cut it lower then 2 1/2 inches in the cooler weather and let it go to 3" in the warmer weather. This will keep moisture in the lawn so you don't have to water as much. Never cut more then 1/3 of the height of the lawn.

Normally you make a straight path then on the way back split the path in 1/2 with just mowed and then next strip. Doing the 1/2 split insures the errant grass gets clipped and stray grass sucked into the bag. Alternate how you mow each time north to south one time east to west the next (or diagonally). Alternating the path will prevent graining.

Every other time let the clippings go on the lawn rather then the bag this will add needed nitrogen to the lawn as it decomposes.

Never cut a wet lawn.

Start the mower on the driveway or another rock free flat area.

Cut the lawn when the sun isn't going to fry you Early AM or Late afternoon.

Always clean gunk out of the bottom of the mower before storing.

Walk at a normal pace behind the mower and don't let it run in one spot without moving it.

Don't drive over tree stumps or rocks or toys or the neighbors cat it pits the blade and then your grass gets shreaded.

Keep little kids 10 feet away if the come closer turn off the mower.

Always mow forward never ever never backward.

Wear crappy sturdy shoes.

Have copious amounts of beer or icetea available on warmer days.

Don't feed the lawnmower after midnight.

Sharpen the blade once a year (more often if you drive over the neighbors cat) don't put it back on backwards.

Never leave it running if you are going even a foot away from it. The lever...Called the deadmans lever will stop the mower when you let go..make sure you pull the key.

If this is the electric model store the battery seperate from the mower.

10 yr old Briggs & Stratton 5HP Quantum Lawn Mower. How to replace wire that stops mower?




Tim


This wire is connected to a bar near to where your hands go to push the mower, that when you let go of it, the mower goes off. I guess it's an emergency safety feature.


Answer
I like to let the safety bar hang down below the handle, some folk like it to be above the handle, anyway the first thing you do is take the old one off and take it to sears to match it up. Replace the cable at the motor first then slide the S connector into the safety bar hole sideways and then twist it. Simple and easy to fix. Don't try and defeat this feature, I have toeless friends that live on the river. Cutting the grass near the bank involves letting the mower go all the way down to the waters edge and sometimes good old boys have one too many beers in em when mowing during summer. After a full day of water sking the last thang you want to do is cut the grass. Not having that feature could cause serious injury.




Powered by Yahoo! Answers

lawn mower blade not low enough to the ground?

best lawn mower uneven ground on Lawn Care Business Cards, 600+ Lawn Care Business Card Templates
best lawn mower uneven ground image



Kay/19


its an older push mower with a newer engine but the blade isn't cutting low enough the adjustable wheels are set to low the blade is sharpened just wondering if i bend the blade on each side so it be low enough in the grass will that cause vibration or even damage
JILL S i don't have money to blow like you
thanks Moon Man



Answer
Bending the blade yourself will make the blade out of balance and the vibration will be very hard on your newer engine. A static balance would be very difficult, a dynamic balance would be impossible by hand. (The reason for the mower not cutting low enough is that the newer engine has a shorter shaft than the original engine had. Someone just put an engine on without any thought to the length of the shaft. Wrong engine, at least wrong shaft length.) Back to bending the blade. If you bent the blade and could be lucky enough to keep it in balance, the end of the blade would be lower than a point say 2" in from the end. This depending on your grass length, how fast your mower runs, how fast you walk etc, etc would result in a very uneven cut. The cutting portion of a mower blade is to rotate parallel to the ground and not at even a slight angle.
Other than replacing the shaft in the engine, there are very few if any ways to lower your blade. For example, additional washers under your blade will not lower it. Additional washers between the blade and the shaft on mowers where the blade makes contact with the shear plate on the shaft, will defeat the shear, safety mechanism, because no resistance would be provided to cause the blade to rotate when it was under load. If a key way is used to transfer power to the blade from the shaft the additional washers may lower the the key-way so that it does not make contact with the key. Again the additional washers will not help. Although it is possible, but not probable, that some scenario exists where washers could help, they are few and far between.
Solutions: Take the mower to an small engine shop and have the crank shaft replaced with a longer shaft like the original engine had. (Not good, this would be a lot of money to put into an old mower.) Better solution: Take your mower to a mower shop and see if they have a blade with more drop, from the factory, that will fit your mower. (If they have one this would be the cheapest solution.) Or possibly see if they have a crank shaft extender that will lengthen the shaft and lower your blade mounting position. (The extenders are used by some manufacturers of mowers as standard mower parts.) Last and probably least would be to find an old mower with smaller wheels and replace your wheels. It would push harder but it would cut shorter.
Notice, not mentioned as a possible solution was bending your blade because it not only will not work it will ruin your motor.

riding mower/tractor stability?




julie_ivyp


I bought a used Crafstsman riding lawn tractor with a 42 inch cut. It is only four years old and is in good shpe. However, the person who sold it to me didn't have the manual. I have no experience with riding mowers and just wondered how steep or uneven the terrain has to be before there is the concern of it tipping over. My backyard has some grade to it and is uneven in spots. It also has mole mounds that make it uneven. As I was mowing, the tractor kind of moves and tilts with the terrain. Is that okay? If the wheels don't come off the ground is it fine? I may be being overly cautious...I just don't know when the possibility of it tipping over might occur. Thanks in advancefor any advice or suggestions!


Answer
Don't push anything.... if you don't feel comfortable doing it... don't do it. Garden tractors generally have a pretty low center of gravity and hold thier ground pretty well. If you have areas you have to mow and the possibility of rolling over is concerning you... you should add weight to the tractor. Wheel weights or filling the tires are a few easy ways to do so. The more weight and the lower it is... the harder it would be to turn over. Be careful.




Powered by Yahoo! Answers